Heavy Wall Adhesive lined heat shrink tubing
Heavy Wall Adhesive lined heat shrink tubing
Features:
- 3:1 Shrink Ratio with melt adhesive inner lining (shrinks to 1/3 its original diameter)
- Longitudinal Shrinkage: up to 10%
- Meets requirements of AMS-DTL-23053/15 (formerly MIL-I-23053/15), Class 1
- UL 224 VW-1 flame retardant (jacket only)
- UL 486D rated for direct burial
- Dielectric Strength 500 V/mil (500 x Jacket Wall thickness x 1000) (for example, a typical tube thickness after shrinking will be about 0.10. Using these caculations, the rating will be about 50,000V, or 50KV)
- Maximum Continuous use temperature 110°C
- Shrink Temperature of 120°C and operating temperature of -55°C to + 110°C
- Crosses to: Canusa CFW, 3M HDT, 3M ITCSN, Tyco Raychem RHW, LG PHWT
- Typical applications include: Electrical insulation - Ideal for exposed or underground applications providing good insulation, waterproofing and mechanical protection. Also suitable for Mechanical and abrasion protection, Physical/Electrical Protection of Components, Strain Relief, and Solder Insulation.
| Diameter | Buy |
|---|---|
| 3/8" | |
| 0.4" | |
| 1/2" | |
| 0.8" | |
| 0.9" | |
| 1.1" | |
| 1.3" | |
| 1.5" | |
| 1.75" | |
| 2" | |
| 2.15" | |
| 2.7" | |
| 3" | |
| 3.75" | |
| 4.5" | |
| 5" | |
| 7.1" |
For direct burial of heavy duty electrical cable, where environmental protection is necessary. Tubing is supplied with an adhesive layer, adding a water tight seal to the strain relief the tubing provides. When exposed to heat (usually a bit lower than the activation temperature of the heat shrink), the inner layer begins to flow (just like a hot melt glue). When the tubing shrinks and cools down, the inner layer forms an adhesion layer between the tubing and the component or wire. This provides a watertight seal, protecting the connector and/or wire in direct burial and submersed applications
-
Dimensions & Technical Specs
|
Diameter
|
Part Number
|
AMS-DTL-23053
|
Min ID before shrinking
|
Max ID after shrinking
|
Wall thickness after shrinking |
Length
|
|
| Jacket | Adhesive | ||||||
| 0.3" | HS3AH-030 | - | 0.30" | 0.1 | 0.08 | 0.01 | 4 ft |
| 3/8" | HS3AH-0375 | /15-108 | 0.354" | 0.118 | 0.079 | 0.01 | 4 ft |
| 0.4" | HS3AH-040 | - | 0.39" | 0.15 | 0.09 | 0.01 | 4 ft |
| 1/2" | HS3AH-050 | - | 0.512" | 0.158 | 0.094 | 0.012 | 4 ft |
| 3/4" | HS3AH-075 | - | 0.750" | 0.24 | 0.09 | 0.014 | 4 ft |
| 7/8" | HS3AH-090 | /15-101 | 0.866" | 0.236 | 0.098 | 0.014 | 4 ft |
| 1.1" | HS3AH-110 | - | 1.1" | 0.315 | 0.12 | 0.014 | 4 ft |
| 1.3" | HS3AH-1375 | /15-109 /15-102 |
1.299" | 0.315 | 0.126 | 0.014 | 4 ft |
| 1.5" | HS3AH-150 | - | 1.5 | 0.47 | 0.16 | 0.015 | 4 ft |
| 1.75" | HS3AH-175 | /15-110 /15-103 |
1.77 | 0.472 | 0.169 | 0.016 | 4 ft |
| 2" | HS3AH-200 | - | 2.00" | 0.63 | 0.17 | 0.017 | 4 ft |
| 2.15" | HS3AH-215 | /15-104 | 2.165" | 0.63 | 0.177 | 0.016 | 4 ft |
| 2.7" | HS3AH-270 | - | 2.70" | 0.87 | 0.17 | 0.017 | 4 ft |
| 3" | HS3AH-300 | /15-105 /15-111 |
2.953" | 0.827 | 0.173 | 0.016 | 4 ft |
| 3.75" | HS3AH-375 | - | 3.74" | 1.18 | 0.169 | 0.018 | 4 ft |
| 4.5" | HS3AH-450 | - | 4.5 | 1.5 | 0.17 | 0.018 | 4 ft |
| 5" | HS3AH-500 | /15-112 /15-106 |
5.11 | 1.42 | 0.17 | 0.018 | 4 ft |
| 7" | HS3AH-700 | - | 7.10" | 1.97 | 0.17 | 0.018 | 4 ft |
Write Your Own Review